We proceeded to paint the ceiling in the Cloakroom a nice sky blue colour (to match the colours in our wallpaper), but we also wanted to create some fluffy clouds so we cut some paper and stuck them to the ceiling, to cover the air vent and the three lighting units. They are of variable size and shape.
We then decided that the clouds are not working so we painted the air vent the sky blue colour, to make it blend in more, and dab various colours of grey and white and blue to make the clouds more fluffy.
Then, we painted the alcove where the vanity unit is going, including either side of the door entrance. This is a blue grey colour that approximately matches the colours in our wallpaper.
Now we are ready to apply the final finishing top coat of resin to the floor. It is a pale grey colour. But, first, we sanded the rough surface, to reduce the obvious join lines and other bumps and rubbed around the edges. We noticed that there were holes so we filled them up with more filler.
Cloakroom floor filled and sanded
After, we were satisfied with the condition of the floor, we proceeded to paint the final resin top coat all over.
While the resin was still wet, we sprinkled icing sugar all over the surface, to help roughen up the surface, to make it a better non-slip surface.
Topcoat applied and sugared
After a day of waiting for the resin to fully cure, we then got a bucket of hot water and poured it all over the floor. Because we deliberately had a small slope rising towards the doorway, none of the water escaped the room at all. We used a sponge to stir the water, to dissolve the sugar and then picked up the dirty water with a couple of sponges. We repeated again with more hot fresh water and sponged it dry. We now have one finished flooring, fully waterproof and easy to clean right around the whole room, including underneath the toilet.
Washing the Sugar off
The next job is to lay on the wallpaper we have bought for our cloakroom. It is special wallpaper and we carefully lined each strip starting with the one immediately behind the toilet and then working one way, leftwards towards the door, and then doing the final two strips to the right of the toilet, coming around on to the linen cupboard and turning a few inches on the side wall. We then carefully trimmed the bottom edge so it neatly terminated to the skirting and then did the same at the top. We had to dab a few edges and joints with more paste to help stick it down.
The next step in decorating the walls, is to put on several coats of varnish all over the wallpaper, to provide a protective and water resistant surface. We put on a third coat immediately behind the toilet itself because it will get even more scrubbed as you would expect.
We then sliced a thin piece of oak off one of our planks and then run it through our router to give it a gentle moon crescent shape. We rubbed it smooth and then gave it a coat of PU varnish with a mid-brown dye. We stuck it on the edge of the wallpaper that just came around the linen cupboard corner. This will protect the edge of the paper from being damaged.
Then we noticed that some of the blue grey walls were showing signs of wear and tear, probably caused by when we were doing the vanity unit and the lower shelf underneath. So, we gave the grey walls a touch up coat of paint.
The next step is a very important one, is the mounting of the toilet!! We carefully cut through the wallpaper to where the two pipes needed to come through the wall, then the two bolts sticking out, ready for the toilet and finally, the square push button module for flushing the toilet. We followed the instructions for measuring the length of the two plastic pipes, one for supplying the flushing water and the bigger pipe to take away the water. We then push the toilet on to the two bolts and made sure that it was level. We tightened the nuts until the toilet was nearly back against the wall, at which point, we ran a line of clear PU sealant between the edge of the toilet and the wall and finish doing up the nuts tight. We carefully scraped any excess away.
And finally, we installed the flush buttons module. We connected the tiny air pipe from the cistern and then clicked the module into place. It has magnets to hold it tight. Very clever.
We then press the button .. and it flushes !!
And no leaks !!
The other thing we did was to connect up a temporary tap to our cold water supply. It is an ordinary tap, with a multi turn knob. Nothing fancy. We now have the ability to have running water. We got soap in a bottle, plus also a bar of soap. We did buy a plug for the sink but it wasn’t a very good quality as it doesn’t hold the water for hours and hours. We will have to find another one.
We then ordered a large mirror measuring 600mm wide by 1200mm tall. It is a frameless and also has hidden hooks so it hangs slightly proud of the wall. We also bought a toilet roll holder and a hand towel holder, plus also a toilet brush and finally, a small swing lid rubbish bin.
Cloakroom Finished 1
Cloakroom Finished 2
The last thing we did for the Cloakroom, was to install the sliding door module. We didn’t get as far as implementing the compress air system because we decided that the sliding mechanism we spent a few weeks designing isn’t working as well as we hoped. We will mount what we got and make use of it for now, but, we will use a different sliding mechanism in the future and replace this one with a new one. We probably will move it to the Kitchen because it is likely that the sliding doors will be rarely used.
So we managed to get the module up inside the wall and screwed it into position. We then got a sheet of OSB board and sliced it up into two 450mm wide by 2100mm tall pieces. We then cut a narrow piece of MDF board and glue that to the edge. Next, we bent a couple pieces of aluminium 40mm wide flat bar to make a couple of L shaped brackets, with a slot cut in the top to allow the hanging of the two halves of the door to hook onto the carriage. We then cut a couple of finger grooves on the edge of both doors, on both sides so that one could open and close them. The last thing we did, was to use short length of draught excluder brushes and mount them near the bottom of the door, one on each side of the door so that the brushes are very slightly pressing into the surface and this holds the door nice and steady.
Temporary Cloackroom sliding doors
This is just a temporary doors, as it is only 11mm thick. We will replace them with proper 45mm thick ones with frosted patterned glass later on.